5 gallon water filling machine 600BPH local technical level improvement degree amazing

5 gallon water filling machine 600BPH is composed of washing, drip drying, filling and gland, which is suitable for the filling production of 3-5 gallon bottled drinking water.The washing process is divided into three steps: alkaline liquid decontamination agent inside and outside washing.Alkaline water, disinfection water can be recycled.The sealing process of the 600 barrel filling machine is controlled by PC computer. The 600 barrel filling machine has safety devices such as chain, signal and self-test.

The 600 barrel filling machine is made of stainless steel, in line with the requirements of food hygiene, reasonable structure, convenient operation, accurate action is currently the ideal equipment for the barrel drinking water production line.

5 gallon water filling machine 600BPH is used for the production of 3-5 gallon bottled drinking water, models are 100, 150, 200, 300, 450, 600, 900, 1200.The barrel filling production line consists of three parts: bottle washing, filling and sealing.The 600-barrel filling machine adopts multi-channel washing liquid spray and disinfectant spray to achieve the purpose of washing and disinfection. The disinfectant can be recycled.The large 600 barrel filling machine can be automatically sealed, and the process of conveying bottle cap is equipped with a shower device to ensure that the bottle cap is sterile and clean.The production line of 600 barrel filling machine can automatically wash, disinfect, fill, gland, count and output.The VAT 600 barrel filling machine has the features of complete function, novel design and high degree of automation. The VAT 600 barrel filling machine is a new type of drinking water bucket equipment integrating machine, electricity and gas.

The working principle of the 600 barrel filling machine is that the empty barrel moves with the chain to a station and washes the mouth and body of the barrel in an inverted shape.The washing process goes through the following procedures: the first drip drying, the second reuse water, the third, fourth and fifth disinfectant, the sixth drip drying, the seventh reuse water inside and outside flushing, the eighth and ninth sterile water inside flushing, and the tenth drip drying (the process can also be set according to user requirements).

The clean bucket is turned over 90 degrees with the movement of the chain, and the empty bucket is pulled out of the bucket seat by the barrel pulling cylinder and turned down with the overturning frame, and then the barrel pushing cylinder is turned upward, so that the empty bucket is placed on the conveyor belt of the filling machine to wait for filling.

After the sterilized empty barrel reaches the filling position, the filling valve is pushed into the mouth of the barrel by the cylinder, and the filling pump opens the filling. The filling time is set by the microcomputer, and the filling time can be corrected by using the multifunctional button on the panel according to the level of the liquid, so as to reach the * position.

After filling, the filled bucket will be sent to the capping station by the conveyor belt. When passing the capping station on the way, the bottle cap will be automatically put on the mouth of the barrel.After the gland is completed, it is output through the conveyor chain and enters the post-packaging process.

Main technical parameters of 600BPH 5 gallon water filling machine:

Equipment model: QGF-600

Main machine station: four rows and ten lanes

Rinse nozzle: up and down movement, into the barrel mouth 100mm

Applicable barrel type: 276×490×56

Suitable cap: 5 gallon Smart cap (56 x 39+17 x 8)

Number of filling heads: four

Gland head number: 1 pneumatic type

Production capacity: 600 b/h

Total power: 8KW, including: washing pump 6, filling pump 2

Air pressure: 0.6--0.8Mpa, gas consumption: 0.4 cubic meters/min

Water consumption: rinsing water 1T/H (among which: disinfection solution is recycled, clean water is reused once), filling water: 6T/H

Weight: about 1500kg

5 gallon water filling machine 600BPH is automatically controlled by PLC program. The working process of the large barrel 600 barrel filling machine is as follows: 1. Close the air leakage protection switch and open the emergency stop switch.2. Place the "selector switch" in the "automatic" state and press the "start switch" button to control the AC contactor of the transmission motor to pull in and the machine starts to work.When the empty bottle is inserted into the empty bottle position and the empty bottle detection sensor switch is pressed down (the flushing signal is sent by the empty bottle detection sensor switch at the bottle washing entrance area), the bottle washing drive motor starts to run, and the empty bottle is brought into each washing disinfection station through the chain and bottle support.(The washing bottle goes through nine stations: * station is drip-dry; the second, third, fourth and fifth stations are rinsed with chlorine dioxide (ClO2 solution) washing and disinfection solution; the sixth station is drip-dry; the seventh and eighth stations are rinsed with clean water; the ninth station is rinsed with pure water. The rinsing time is as follows:* Station is drip dry 12S, the second, third, fourth and fifth stations are 16S, the sixth station is drip dry 12S, the seventh and eighth stations are 15S, the ninth station is 8S).When the drive motor runs with the empty bottle and enters the positioning induction area with the induction piece on the chain, the positioning induction switch sends out a signal to stop the drive motor and start the water pump of the flushing bottle at the same time to carry out the corresponding flushing and disinfection work (the flushing time is controlled by the PLC program);After washing, the washed empty bottle falls on the push bottle stand through the transmission mechanism of washing bottle. The push bottle cylinder works and pushes the empty bottle to the filling position, so that the filling nozzle is aligned with the mouth of the water bottle, and the filling pump starts filling.(The filling time can be adjusted by the user according to the needs), when the filling is full, the PLC will send the control signal, the filling solenoid valve is closed, and the filling will stop. After the filling, the bottle driving motor will send the filled water bottle to the capping area and the capping area, and the capping cylinder will drive the capping device to press the bottle cap tightly.At this point, a wash and irrigation cycle is complete.

If you are in the field of drinking water production and want to start a new project or upgrade the automated production line

Getting 5 gallon water filling machine 600BPH from a reliable supplier is the best way.

Please contact us now to find out how we can help you with your project.